NewPro-Maintenance Kit for Shower and Bath

The efficient coating – and aftercare set for coated and non-coated surfaces

Product Description

NewPro-Maintenance Kit for Shower and Bath is an efficient coating and care set for a large number of glass and glazed ceramic surfaces in showers and baths. The set includes NewPro-Active Cleaner, which is an environmentally safe base cleaner for the removal of soap remains, chalk and other debris and deposits. NewPro-Nano Active Protection is a nano-sealant for the maintenance and refreshment of previous surface coatings and offers a fresh and hygienic ambiance just like on the first day.

Range of Application and Use

NewPro-Maintenance Kit for Shower and Bath was specially developed for the refreshment of already coated surfaces in sanitary facilities. The especially includes:

• Ceramic
• Glass
• Glazed ceramic surfaces such as tiles.

Product Characteristics

NewPro-Maintenance Kit for Shower and Bath offers the coated surface dirt repellent properties without change to the optics of the surface. The coated surfaces display an above average durability and remain presentable for a longer time. Further characteristics include:

• Easy to apply
• Easy-to-clean-Effect – easy cleaning and care of the surface
• Environmentally friendly, due to a lack of solvents
• Fast drying
• Free of alergy-triggering outgassings and solvent-containing adhesives
• Grease, oil, dirt and water repellent – strongly hydro- and olephobic
• High efficiency through efficient use
• Odorless
• Resistant against UV-irradiance
• Short drying times.

Durability

Written guarantee for surface protection with NewPro-Maintenance Kit for Shower and Bath:

• Stability of the surface protection for a minimum of 10 years with the correct application and heedance to the instructions for further care.

Instructions Regarding Use/Application

Surface preparation/pre-cleaning: All surfaces should be grease, oil and dust particle free, dry and sustainable. 1. Large and rough dirt or soiling and lose partials, as usual, should be thoroughly removed In the event of extreme soiling or dirt, repeat this step again. 2. Moisten the enclosed sponge with water 3. Apply an appropriate quantity of NewPro-Active Cleaner to the surface and rub it over the entire soiling and dirt 4. Leave NewPro-Active Cleaner standing to take effect for a short period and afterwards rinse off with clean water.

Application: The surface to be coated must be completely cleaned and grease free prior to the application. 1. Lightly spray NewPro-Nano Active Protection onto the surface consistently and evenly in surface parts between 0. 5 und 1. 0 m and distribute and polish with the towel included in the set. 2. Leave the coated surface to dry for 2 - 5 minutes. 3. If necessary remove extra materials with a lint free towel or spread evenly.

Notice: NewPro-Maintenance Kit for Shower and Bath covers a wide range of applications. For this reason, we recommend a test be carried out to the surface to determine the suitability of the product. The surface should be immediately coated after the pre-cleaning and should no longer be touched by hands.

Mixing Instructions: If necessary, NewPro-Active Cleaner is mixable with water. The ratios are noted on the package, but the degree of soiling or dirt must also be considered. NewPro-Nano Active Cleaner comes ready to apply and can be directly applied to the surface. A mixture with foreign substances can negatively affect the properties, the durability of the product, and the applied protective coating.

Use:

• The set is sufficient for the maintenance of a surface for up to 6 m.

This is simply an estimation, which can vary depending upon the absorbency of the surface and the degree of soiling and dirt. An exact amount of material required should be determined by a test on the intended surface.

Care Instruction

Improvement and New Surface Coatings: The surface coating is designed to last for many years. In the event that this not is the case, and the surface protection shows damage, repeat the above-described steps in applying a new coating.

Cleaning of the coated surface: NewPro-Maintenance Kit for Shower and Bath is a permanent protection system. Soiling and dry remains can be removed with a moist towel.

Caution: The application of very aggressive cleaning detergents such as scrubbing detergents or abrasive powder, highly concentrated drain pipe cleaner, fixture and steel cleaners such as powder bath cleaners which can cause damage to the protective coating should be absolutely avoided. Surface damaging scrubbing devices are may also not be used.

Required Conditions for Use/Application

The application and drying requires a surface and area temperature between min. +5°C and max. +30°C. NewPro-Maintenance Kit for Shower and Bath may not be applied under direct sunlight at temperatures over +25°C and at surface and area temperatures under +5ºC. During drying the surface must be protected against moisture.

Drying Times:

• Immediately after the application. If necessary, rub with a lint free towel.

The complete protective properties of NewPro-Maintenance Kit for Shower and Bath results after a 12 to 24 hour drying time at a temperature of +20°C; depending on the temperature and the relative humidity.

Cleaning of tools:

• In freshly used condition, clean with lots of clean water.

Delivery Form

Units per Package:

• 250 ml NewPro-Active Cleaner bottle (cleaner)
• 100 ml NewPro-Nano Active Protection spray bottle (sealant)
• Active Protection-Towel
• Sponge.

Further types of packaging, sizes, and colors are available upon request.

Color:

• Colorless.

Special Instructions

Transport:

• Unlabeled and non-hazardous.

Storage:

• At a temperature range between +4°C to +30°C min. 6 months in tightly sealed original packaging
• Protect against moisture, frost, and heat.

For further instructions, please refer to the product safety data sheets for this product.

Disposal:

• Dispose of product remains/rest at the officially designated disposal site
• Do not dispose of the product through the public sewage system, drains or other accesses to sewage systems
• Only recycle completely emptied containers.

Work Hygiene

Before breaks and at the end working with the product, wash hands thoroughly. Do not eat, drink or smoke during use. Avoid eye and skin contact with the product. If necessary, wear protective clothing.

For further safety and protective measures please see the product safety sheets of the product.

Safety Precautions

Keep away from children. Keep containers sealed tightly closed. In the event of eye contact, immediately flush eyes out with water. In the event of skin contact, wash skin thoroughly with water and soap. If necessary, seek medical advice. Do not smoke during application and use. If swallowed seek immediate medical advice and show the packaging or product label to the treating physician. NewPro-Maintenance Kit for Shower and Bath is not to be applied to surfaces which can reach temperatures over +450°C, otherwise the coating surface layer can become brittle and damaged. NewPro-Active Cleaner is not to be applied to acid sensitive materials such as marble and other natural stone.

For further safety and protective measures please see the product safety sheets of the product.

Safety and Protective Measures

The general safety precautions for water solvent materials are to be considered. The technical advice regarding the use and application of our products is the result of extensive research and development as well as many years of experience, according to the best of our knowledge. The different kinds of requirements of an object, under varying conditions, make it necessary for the user to check the suitability for the intended purpose. We reserve the right to effectuate changes, which serve to affect the technical advance or improvement of our product.

For further safety and protective measures please see the product safety sheets of the product.